Feiss F1882-5 User Manual download pdf

(E) REV 3/05

ASSEMB LY I NST R UCT I ONS FOR F1882/5

MUR R AY FEI SS

©M UR R AY FEI SS I M PO RT COR P.

Bulb

(not included)

Socket

FIG: 1 CHAIN HUNG INSTALLATION

FIG: 2 FLUSH MOUNT

INSTALLATION

Mounting Plate

Machine Screws

Note: Spare crystals enclosed in hardware bag.

Fixture Wire

and Ground Wire

Fixture Loop

Threaded

Chain Link

Fixture Plate

Canopy Loop

Ball Cap

Nuts

Chain

Threaded

Chain Link

Candle Tube

Canopy

Loop

Lock Washer &

Hex Nut

Fixture Plate

Ball Cap Nut

Canopy Leaf

Short

Threaded

Pipe

1 2 3 4 5 6

1 pc. 1 pc. 10 pc. 10 pc. 5 pc. 20 pc.

Glass Shade

Fitter

Bottom Assembly

Fixture Wires

IMPORTANT

TURN OFF POWER AT MAIN FUSE OR CIRCUIT

BREAKER BOX BEFORE STARTING INSTALLATION

Carefully unpack and identify all parts before assembly.

Bulbs are not included.

1. Install bottom assembly by screwing into bottom of fixture.

2. Place candle tubes over candelabra sockets and screw bulbs

(not included) into sockets to secure. See relamping label on candle

tube for type and maximum allowed wattage.

3. Hang all crystal glass parts as shown on drawing.

NOTE: To replace broken crystals or pins extras are included in

hardware bag. To replace broken crystals open pins, remove crystal,

hook new one, then close back pin. Avoid bending pins into

sharp angle.

4. This fixture can be mounted onto ceiling either as chain hung

or flush mount:



CHAIN HUNG INSTALLATION- Fig. 1:

A. Take fixture wire (with plastic insulation) and ground wire and

thread through fixture loop. Then install loop onto threaded pipe

located at top of fixture.

B. This fixture is supplied with 2 threaded chain links. These links

are opened and closed by twisting cylinder on chain link. One

threaded chain link should be installed onto canopy loop and the

other should be installed onto fixture loop. The standard chain should

be installed in between these 2 threaded chain links.

C. Determine the desired length of chain to hang. Remove any

unwanted links with chain plier.

D. Take ground wire and weave through above chain links, then

thread through center hole in canopy loop. Repeat with fixture

wire (wire with plastic insulation).

FLUSH MOUNT INSTALLATION- Fig. 2:

A. Remove and discard canopy loop and threaded pipe from

fixture plate.

B. Thread ground wire and fixture wire through fixture plate,

lock washer, and hex nut. Lock all together on top of fixture by

tightening hex nut onto threaded pipe.

5. Cut excess wires leaving only 6" (15cm) length of wires above

canopy. Split fixture wire into two strands. Then strip off 3/4"

(19mm) of outer plastic insulation.

6. Follow enclosed “Multiple Standard Installation Instructions”

for electrical and fixture installation onto ceiling outlet box.

NOTE: Before starting wire connection, enlist a helper to support

the fixture, or make a hook from a wire coat hanger and temporarily

suspend the fixture from mounting plate.

7. Install glass shade by inserting into fitter located at center of fixture.

Make certain it sits securely inside.

MUR R AY FEI SS 1

Summary of Contents

Page 1 - MUR R AY FEI SS

(E) REV 3/05ASSEMB LY I NST R UCT I ONS FOR F1882/5MUR R AY FEI SS©M UR R AY FEI SS I M PO RT COR P.Bulb (not included)SocketFIG: 1 CHAIN HUNG I

Comments to this Manuals

No comments

Feiss F1882-5 User Manual

Browse online or download User Manual for Lighting Feiss F1882-5. Feiss F1882-5 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Lighting Feiss F1882-5